Cara Mengatasi Error 720 Dial-Up Conecction

To resolve this issue, uninstall the TCP/IP protocol, remove the second WAN Miniport IP device, and then reinstall the TCP/IP protocol. To do so, follow these steps:

1. Uninstall the TCP/IP protocol. To do so:
   1. In Control Panel, double-click Network and Dial-up Connections, right-click Local Area Connection, and then click Properties.
   2. Under Components checked are used by this connection, click Internet Protocol (TCP/IP), and then click Uninstall.
   3. Follow the on-screen instructions to uninstall TCP/IP.
   4. Restart the computer when prompted, but click No if you are prompted to allow Windows to enable a protocol.
2. Right-click My Computer, and then click Properties.
3. Click the Hardware tab, and then click Device Manager.
4. On the View menu, click Show hidden devices.
5. Under Network adapters, there should be no WAN Miniport IP devices. If a WAN Miniport IP device is listed, continue to the following step. If no WAN Miniport IP device is listed, go directly to step 16.
6. Click Start, click Run, type regedit in the Open box, and then click OK.
   
   Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following article number to view the article in the Microsoft Knowledge Base:
   322756 How to back up and restore the registry in Windows
7. Locate the following registry subkey:
   HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\{4D36E972-E325-11CE-BFC1-08002BE10318}
8. On the Registry menu, click Export Registry File, type backup-key in the File name box, and then click Save.
   
   Note You can restore the changes that you make to this registry key. To do so, double-click the backup-key.reg file that you saved.
9. Click each of the registry subkeys under this key, and then view the Data column of the DriverDesc value to determine which of the subkeys corresponds to WAN Miniport (IP). For example, the 0005 subkey.
10. Right-click the subkey whose DriverDesc value data is WAN Miniport (IP) (for example, right-click 0005), and then click Delete. Click Yes to confirm that you want to delete the key.
11. Quit Registry Editor.
12. Right-click My Computer, and then click Properties.
13. Click the Hardware tab, and then click Device Manager.
14. On the View menu, click Show hidden devices.
15. Under Network adapters, right-click WAN Miniport (IP) and then click Uninstall. Click OK to confirm that you want to remove this device.
16. Reinstall the TCP/IP protocol. To do so:
    1. In Control Panel, double-click Network and Dial-up Connections, right-click Local Area Connection, and then click Properties.
    2. Click Install.
    3. In the Select Network Component Type dialog box, click Protocol, and then click Add.
    4. Under Network Protocol, click Internet Protocol (TCP/IP), and then click OK.
    5. When the protocol is installed, click Close.
17. Reset the modem by turning the power off and then on, or for an internal modem, restart the computer.
18. Test your Internet connectivity.

** http://support.microsoft.com/kb/810979**

Error 720: No PPP Control Protocols Configured

To resolve this behavior, follow these steps:

1. Find out which protocols the RAS server is running, and make sure that the RAS service is installed and configured properly (or ask the Network Administrator to do this).
2. After you find out which protocols the RAS server is running, make sure that your Windows XP-based computer is running one of the same protocols that the RAS server is running:
   1. Click Start, click Control Panel, and then double-click Network Connections.
   2. Under Virtual Private Network, right-click the VPN connection, and then click Properties.
   3. In the VPN Connection Properties dialog box, click the Networking tab, and make sure that you have a protocol that the RAS server is running.
3. If you do not have a protocol that the RAS server is running, add the needed protocol:
   1. Click Install, click Protocol, and then click Add.
   2. Click the protocol that you need to install, and then click OK.
   3. Click Close in the VPN Connection Properties dialog box.